SophiaReed & Camelot
SophiaReed SophiaReed
Hey Camelot, I’ve been crunching numbers on the tensile strength of medieval steel—trying to figure out how those ancient blades could survive the heat and force of a clash. What do you think was the true edge of a sword back in your era?
Camelot Camelot
Ah, the very thought of a blade’s edge in the days of knights is a thrill! The true edge of a sword was not merely a sharp line, but the culmination of centuries of ironwork and a smith’s art. In the age of the long swords, the edge was often left very thin, sometimes only a fraction of an inch across, to allow the blade to slice cleanly through armor or flesh. That thinness, however, required a high carbon content and a careful quenching process to harden the edge without making the whole blade brittle. The smith would temper it afterward, a gentle reheating to relieve stresses and give the edge a little give. So the true edge was as much about the science of steel—heat, quench, temper—as it was about the lore of a knight’s courage. If you’re crunching numbers, remember: a sword must balance hardness with resilience, or it will shatter in the heat of battle.
SophiaReed SophiaReed
Sounds like a fascinating blend of art and science—exactly the kind of interdisciplinary puzzle I enjoy. If you can share the carbon percentages you’re working with and the cooling rates you’ve tested, I might be able to run a quick model to see how the hardness and toughness trade‑off plays out. The key is keeping the gradient of microstructure across the blade; a too‑uniform hardening can cause that brittle failure you mentioned. Let me know what data you have and we can tweak the heat‑treatments together.
Camelot Camelot
I appreciate your enthusiasm for the science of steel. In the medieval forge, the smiths typically worked with a carbon content of roughly 0.7 to 1.5 percent. That range allowed the blade to be hardened enough to hold a keen edge while still retaining a modest amount of toughness. As for cooling rates, a slow quench in oil could be considered a moderate rate—perhaps a few minutes to reach room temperature—while a rapid quench in cold water could bring the temperature down in under a minute. The key is to avoid too uniform a hardening; the smith would often leave a slight gradient, harder at the edge and slightly softer toward the spine, to prevent brittleness. If you run a model with those parameters, remember to temper the steel after hardening—reheating it to about 300 to 400 °C and holding for an hour or two—to relieve stresses and improve toughness. Feel free to tweak the numbers, and we can see how the balance shifts.
SophiaReed SophiaReed
Got the ranges, that’s a good start. I’ll set up a finite‑element model with a 1.2 % carbon alloy and a two‑step quench: 30 s in oil then 20 s in water. After that, a 350 °C temper for 90 minutes should give a decent balance. I’ll log the hardness profile and impact toughness along the blade. Let me know if you want me to tweak the cooling curve or the temper duration.
Camelot Camelot
Your plan sounds very reasonable. The 1.2 % carbon gives a good mix of hardness and toughness. The two‑step quench should create that gradient you mentioned, with the edge slightly harder than the spine. A 350 °C temper for 90 minutes will relieve stresses and add some ductility. I’ll be glad to review the hardness and toughness results once you have them. If the edge still feels too brittle, we could try a longer temper or a slightly lower cooling rate during the oil step. Keep me posted on the numbers.
SophiaReed SophiaReed
I ran the simulation. The edge hardness is about 58 HRC, the spine drops to 50 HRC. Impact toughness at the edge is roughly 20 J, while the spine is around 35 J. The gradient looks good—no sudden jumps. It’s a bit on the brittle side for the edge, so extending the temper to 120 minutes or lowering the oil quench to 45 s should smooth that out. Let me know which tweak you’d prefer.
Camelot Camelot
A longer temper of 120 minutes would be my choice. The slight extension should give the edge a bit more ductility without compromising the hardening gradient. The oil quench time of 45 seconds is acceptable, but the temper gives a steadier result, so I’ll go with the extended temper. Keep an eye on the hardness—if it drops below 55 HRC you might still need to tweak.