Solidman & Robinzon
Solidman, ever tried building a shelter that can outlast a hurricane and a season of squirrels? I’ve got a blueprint that uses the forest’s own timber, a compass for exact angles, and a bit of firewood trickery that makes the roof almost self‑repairing. Interested in the details?
Sure, give me the blueprint. I’ll check the load calculations, make sure the timber meets the specs, and verify the self‑repair roof trick doesn’t compromise the roof’s integrity. Need all the details before we start.
Here’s the skeleton of the shelter plan—no fancy diagrams, just the essentials you’ll need to check.
Structure
- Frame: 4‑by‑6 timber posts spaced 4 ft apart, topped with a 12‑by‑12 floor slab of cross‑cut boards.
- Walls: Plywood sheathing covered with a waterproof bark‑skin, seams sealed with resin‑based compound.
- Roof: A two‑slope design, pitch 35°, covered with cedar shingles.
- Load: Designed for a 30 lb snow load and wind pressure of 80 psf.
- Self‑repair trick: A hidden layer of flexible resin between the outer shingle and the inner plywood. If a shingle cracks, the resin expands under heat and pushes the shingle back into place. Tested with a 3‑month field test; no leakage observed.
Timber specs
- Hard pine, grade 2, moisture content <10 %.
- Each 4‑by‑6 post: 1 ft core, 2 in. end grain, treated with borate solution for insect resistance.
You can calculate the moment of inertia for the roof trusses using the standard formula for a simple beam. The shear capacity will be above the required 500 lb for wind shear.
Let me know if you need the exact numbers or the resin mix ratio. I’ll send the spreadsheets and the exact wood species list.
Looks solid. Send the spreadsheets and resin mix ratio so I can run the load and shear checks, then we’ll confirm the post spacing and resin performance under temperature swings. No more fluff, just the numbers.
Post spacing 4 ft.
Floor slab 12 by 12 ft, cross‑cut 2 in boards, core 1 in.
Roof pitch 35°, cedar shingles 1.5 in.
Resin mix: 70 % clear epoxy, 20 % polyester resin, 10 % carbon‑fiber powder.
Tested at –10 °C and 40 °C, shrinkage <0.5 %.
Shear capacity of roof truss: 520 lb, wind shear: 80 psf.
Snow load design: 30 lb, safe factor 2.
Let me know if you need the spreadsheet cells for the I‑value of the roof truss or the moisture‑content graph.
I’ve got enough to run the checks. Just send the spreadsheet cells for the I‑value, then I’ll confirm the shear numbers and the moisture graph. No delays.
I‑value for the roof truss (b = 4 ft, h = 2 in, convert h to ft: 0.1667 ft):
I = (b × h³) / 12
= (4 × 0.1667³) / 12
≈ 0.00077 ft⁴
In Excel:
B2 = 4 (b in ft)
B3 = 0.1667 (h in ft)
B4 = =B2*POWER(B3,3)/12 (I‑value in ft⁴)
For shear:
Shear capacity cell B5 = 520 lb (given).
Snow load check: B6 = 30 lb.
Moisture graph:
C2 = “Date”
C3 = “Moisture %”
Populate with your field data. No delays.
Got the I‑value and the shear data. I’ll pull up the spreadsheet, run the checks, and get back to you with any adjustments. No more delays.
Got it. Keep the numbers tight, and ping me if the shear ends up lower than 520 lb or the I‑value falls below 0.00077 ft⁴. Good luck.